Need your opinions !
13-Sep-2003 | 02:17 PM
#1
Thread Starter
Senior Member
Joined: Jan 2003
Posts: 30,142
From: Your sisters bedroom
Need your opinions !
Ok,
These are the things I need to get done to my car:
1) Header bolt broke inside my block, need to get that drilled out and fixed.....
2) Need to get my car tuned. VAFC and everything to gain maximum whp out of it.
3) IACV needs to be cleaned or replaced
4) Valve cover gasket/ cam seal gasket needs to be replaced.
I need a very reputible shop for this that can do all of these or alot of them to save on labour. I will be paying CASH if that makes a difference. Thanks
These are the things I need to get done to my car:
1) Header bolt broke inside my block, need to get that drilled out and fixed.....
2) Need to get my car tuned. VAFC and everything to gain maximum whp out of it.
3) IACV needs to be cleaned or replaced
4) Valve cover gasket/ cam seal gasket needs to be replaced.
I need a very reputible shop for this that can do all of these or alot of them to save on labour. I will be paying CASH if that makes a difference. Thanks
13-Sep-2003 | 04:33 PM
#3
Registered User
Joined: Apr 2002
Posts: 2,990
From: No fixed address
Re: Need your opinions !
1) Header bolt broke inside my block, need to get that drilled out and fixed.....
HAPPY: if you have an exhaust leak, fix it. If it still seals fine. Leave it until you need to do something else to the car and get it done together.
2) Need to get my car tuned. VAFC and everything to gain maximum whp out of it.
HAPPY: For one stop VAFC Dyno tuning, as much as it kills me to say it your best bet, other than doing it yourself, is Yoshio over at Japanese Automotive. They have an inhouse dyno and Yoshio is an absolute guru when it comes to VAFC B-series honda tuning. The price may be up, but you may get some nice results.
3) IACV needs to be cleaned or replaced
HAPPY: Get off you lazy *** and do it yourself
4) Valve cover gasket/ cam seal gasket needs to be replaced.
HAPPY: Get off you lazy *** and do it yourself
HAPPY: if you have an exhaust leak, fix it. If it still seals fine. Leave it until you need to do something else to the car and get it done together.
2) Need to get my car tuned. VAFC and everything to gain maximum whp out of it.
HAPPY: For one stop VAFC Dyno tuning, as much as it kills me to say it your best bet, other than doing it yourself, is Yoshio over at Japanese Automotive. They have an inhouse dyno and Yoshio is an absolute guru when it comes to VAFC B-series honda tuning. The price may be up, but you may get some nice results.
3) IACV needs to be cleaned or replaced
HAPPY: Get off you lazy *** and do it yourself
4) Valve cover gasket/ cam seal gasket needs to be replaced.
HAPPY: Get off you lazy *** and do it yourself
13-Sep-2003 | 04:55 PM
#4
Registered User
Joined: Apr 2002
Posts: 3,084
Re: Re: Need your opinions !
Originally posted by HAPPY
1) Header bolt broke inside my block, need to get that drilled out and fixed.....
HAPPY: if you have an exhaust leak, fix it. If it still seals fine. Leave it until you need to do something else to the car and get it done together.
2) Need to get my car tuned. VAFC and everything to gain maximum whp out of it.
HAPPY: For one stop VAFC Dyno tuning, as much as it kills me to say it your best bet, other than doing it yourself, is Yoshio over at Japanese Automotive. They have an inhouse dyno and Yoshio is an absolute guru when it comes to VAFC B-series honda tuning. The price may be up, but you may get some nice results.
3) IACV needs to be cleaned or replaced
HAPPY: Get off you lazy *** and do it yourself
4) Valve cover gasket/ cam seal gasket needs to be replaced.
HAPPY: Get off you lazy *** and do it yourself
1) Header bolt broke inside my block, need to get that drilled out and fixed.....
HAPPY: if you have an exhaust leak, fix it. If it still seals fine. Leave it until you need to do something else to the car and get it done together.
2) Need to get my car tuned. VAFC and everything to gain maximum whp out of it.
HAPPY: For one stop VAFC Dyno tuning, as much as it kills me to say it your best bet, other than doing it yourself, is Yoshio over at Japanese Automotive. They have an inhouse dyno and Yoshio is an absolute guru when it comes to VAFC B-series honda tuning. The price may be up, but you may get some nice results.
3) IACV needs to be cleaned or replaced
HAPPY: Get off you lazy *** and do it yourself
4) Valve cover gasket/ cam seal gasket needs to be replaced.
HAPPY: Get off you lazy *** and do it yourself
but going to Yoshio, you better show him the money
Else he'll brush you off like dust on the floor. If R0Y sees this, he can add his story about his friend who had work done by Yoshio.
However, that's not to say Yoshio isn't excellent, but his background is Toyota and I think he's quite loyal to the Toyota layout and tuning, though very knowledgable in Hondas as well
But what do I know, I'm only hearing stories
13-Sep-2003 | 05:24 PM
#5
Registered User
Joined: May 2002
Posts: 383
From: Stank_town
Yoshio is the Best in T.O but like they boys said BEND over
also every builder has blown a motor once in there life so dont think that he is perfect. but with his list of skills from TRD and toyota im willing to bet that he can do anything you want RICER
also every builder has blown a motor once in there life so dont think that he is perfect. but with his list of skills from TRD and toyota im willing to bet that he can do anything you want RICER
13-Sep-2003 | 07:45 PM
#7
Registered User
Joined: Sep 2003
Posts: 324
From: Ottawa
except for the VAFC tuning, you can do all of those maintenance things yourself (unless youve got a dyno in your garage )...for the broken stud...go to sears and get their stud/bolt removal kit....its less than $50 I think...plus its a godsend...on par with the Snap-On equivalent but like a third of the cost! The other things just require some wrenching!
)...for the broken stud...go to sears and get their stud/bolt removal kit....its less than $50 I think...plus its a godsend...on par with the Snap-On equivalent but like a third of the cost! The other things just require some wrenching!
14-Sep-2003 | 03:48 AM
#9
Registered User
Joined: Oct 2002
Posts: 3,657
From: Stoney Creek, Ontario
man
I'm 5min away and I can change the sensor/valve, and do the valve cover gasket **** for you... heck I just changed my balljoint and axle yesturday... I'm learning fast
Don't waste your money on easy stuff like that,,, unless you want to?
I'm 5min away and I can change the sensor/valve, and do the valve cover gasket **** for you... heck I just changed my balljoint and axle yesturday... I'm learning fast
Don't waste your money on easy stuff like that,,, unless you want to?
14-Sep-2003 | 12:41 PM
#13
Thread Starter
Senior Member
Joined: Jan 2003
Posts: 30,142
From: Your sisters bedroom
ok, i'm going to go to honda tomorrow to get the valve cover gasket. Is the valve cover gasket for a JDM motor the same as a USDM motor ?
What should I tell the guy what I need ?
Last time I went there, he was fooking clueless cuz I said I have a 2nd gen JDM b16. he was like huh, I was like a SiR motor from japan 2nd generation... he was like HUHHHH. Then I just left. So does anyone have a part number or something ? It would be GREATLY appreciated
What should I tell the guy what I need ?
Last time I went there, he was fooking clueless cuz I said I have a 2nd gen JDM b16. he was like huh, I was like a SiR motor from japan 2nd generation... he was like HUHHHH. Then I just left. So does anyone have a part number or something ? It would be GREATLY appreciated
14-Sep-2003 | 12:41 PM
#14
Thread Starter
Senior Member
Joined: Jan 2003
Posts: 30,142
From: Your sisters bedroom
Originally posted by civic_fan
your only choice for the bolt then is to drill it out and then re-tap the hole....its a bitch...if its not leaking, Id say leave it be!
your only choice for the bolt then is to drill it out and then re-tap the hole....its a bitch...if its not leaking, Id say leave it be!
14-Sep-2003 | 12:54 PM
#15
Registered User
Joined: Oct 2002
Posts: 3,657
From: Stoney Creek, Ontario
Originally posted by 2 rice 4 u
ok, i'm going to go to honda tomorrow to get the valve cover gasket. Is the valve cover gasket for a JDM motor the same as a USDM motor ?
What should I tell the guy what I need ?
Last time I went there, he was fooking clueless cuz I said I have a 2nd gen JDM b16. he was like huh, I was like a SiR motor from japan 2nd generation... he was like HUHHHH. Then I just left. So does anyone have a part number or something ? It would be GREATLY appreciated
ok, i'm going to go to honda tomorrow to get the valve cover gasket. Is the valve cover gasket for a JDM motor the same as a USDM motor ?
What should I tell the guy what I need ?
Last time I went there, he was fooking clueless cuz I said I have a 2nd gen JDM b16. he was like huh, I was like a SiR motor from japan 2nd generation... he was like HUHHHH. Then I just left. So does anyone have a part number or something ? It would be GREATLY appreciated
THats what I did,,, because they were clueless when I went down as well.
Get the spark plug gaskets and the valve cover gasket.
14-Sep-2003 | 01:00 PM
#16
Thread Starter
Senior Member
Joined: Jan 2003
Posts: 30,142
From: Your sisters bedroom
Originally posted by Tman
just tell them 99-00 SIR
THats what I did,,, because they were clueless when I went down as well.
Get the spark plug gaskets and the valve cover gasket.
just tell them 99-00 SIR
THats what I did,,, because they were clueless when I went down as well.
Get the spark plug gaskets and the valve cover gasket.
How much did you pay ? I'm going to have to take money outta the bank due to no bank card
14-Sep-2003 | 01:21 PM
#17
Senior Member
Joined: Jun 2003
Posts: 5,558
From: Saskatoon
Re: Re: Need your opinions !
HAPPY: For one stop VAFC Dyno tuning, as much as it kills me to say it your best bet, other than doing it yourself, is Yoshio over at Japanese Automotive. They have an inhouse dyno and Yoshio is an absolute guru when it comes to VAFC B-series honda tuning. The price may be up, but you may get some nice results.
14-Sep-2003 | 01:38 PM
#18
Thread Starter
Senior Member
Joined: Jan 2003
Posts: 30,142
From: Your sisters bedroom
Re: Re: Re: Need your opinions !
Originally posted by Brett
Do you have contact info for Japanese Automotive? Im in need of some engine tuning.
Do you have contact info for Japanese Automotive? Im in need of some engine tuning.
eh? You live in carisle ? Why dont you come to the stoney creek meets ? Its not too far for you !
14-Sep-2003 | 04:45 PM
#20
Registered User
Joined: Oct 2002
Posts: 3,657
From: Stoney Creek, Ontario
Originally posted by civic_fan
Well...doesnt that just suck!!! your only choice is to drill out the stud and re-tap the hole....good luck....Its a pain in the ***!!!
Well...doesnt that just suck!!! your only choice is to drill out the stud and re-tap the hole....good luck....Its a pain in the ***!!!
